Skip to Content

Category Archives: DC MOTORS – BRUSHLESS – P.P. AND DRIVERS

Stepping motor

The stepper motors are substantially synchronous motors without brushes constructively made to transform, by means of the control electronics, control pulses into precise movements (steps) mechanical, with extreme simplicity of use, for the majority of cases open loop.

Typically, it is referred to 2-phase stepper motors (200 steps per revolution) and 5 stages (500 steps per revolution).
Used in applications where one wants to exploit greater torque at low speed, it doesn’t require the control position with the engine stopped because perfectly blocked by the very nature of the construction of the engine.

A) 2 phases Stepper Motors in the standard version (torques up to 20 Nm) and high performance version (high torque and efficiency, lower noise and vibrations, torques up to 25 Nm).
Control electronics consisting of bipolar chopper drives, DC power and AC, card versions, box and rach.
Power up to 240 VDC, 14 A / phase max.
Operating from 200 to 4,000 steps / rev (microstepping).

B) 5 phases Stepper drives motors, with torques up to 37 Nm (version with reducer)
Powers 24-36 VDC and 200-300 VAC single phase.
Combination with several standard types of gearboxes, also in “harmonic”

C) Stepper systems “closed loop control” with position sensor on the rotor, used to prevent the loss of synchronism in the motor movement.
Torques up to 37 Nm in the version with reducer “harmonic”
24VDC and 200-230 VAC single phase
Operating from 500 to 10,000 steps / rev.

sidac-system

  • Applications where  high torque and low speeds are reqiured
  • Tables X Y
  • Palletizers and “pick&place” systems
  • Packaging, dosing and labeling machines
  • Screen printing machines
  • Robots and actuators in operating machines
  • Handling linear guides belt and / or ball screw
  • Measurement Systems
  • Sewing machines
  • Automatic filling machines
  • Instrumentation and laboratory analysis
  • Orientation / alignment systems
  • Remotes


 

 

0 Continue Reading →

DC: Drivers, motors and servomotors

DC motors and servo motors, with permanent magnets, are built to be used in a wide range of industrial applications, which require high dynamic, torque / inertia and fast acceleration. Great smooth rotation even at very low speeds.

Range of nominal and continuous torques with locked rotor from 0.05 up to 30.00 Nm.
Windings for speed range from 1,000 to 4,000 revolutions / minute.

Possible availability for:

  • tachogenerator with different voltage gradients V / 1000 rpm
  • D.C. safety brake
  • mechanical interfaces B3, B5, B14 with fringes PAM56 / B14 63 / B14 71 / B14 63 / B5, 71 / B5
  • double shaft projection
  • predisposition for encoder attack
  • supply via box terminals, connectors MS, simple cable or shielded
  • forced ventilation in single-phase power
  • possibility mounting planetary gears
  • Insulation class F, protection IP44 and IP54

Mosfets and transistors PWM drive running closed with single-axis adjustments for:

  • rated current peak
  • voltage value and speed of tachometer dynamo in armature feedback
  • ramps for acceleration / deceleration

Rated currents from 5 to 28 with food for double value.

Input power from 45 to 145 VAC (200 VDC)

Voltage protection, overtemperature, short-circuit motor terminals, tacho failure, lack of power phase.

Options of ramps + tacho rupture or ramp + armature feedback

Inductances

Single-phase and three-phase transformers

sidac-systemsidac-system


  • Applicable in in various fields of motion control
  • Operating machinery
  • Machine tools
  • Transfer lines and positioning
  • X Y and rotary tables
  • Axis translations for lathes, milling machines, grinding machines


Drivers for permanent magnet motors: available only in Italian versions:

KERNEL SERIES DRIVEmod. 8/60 ( 8A    nominali  16A  picco / 60Vcc )
JOLLY SERIES DRIVEmod. 10/60 ( 10A nominali 20A picco / 60Vcc )
JOLLY SERIES DRIVEmod. 15/60 ( 15A nominali 30A picco / 60Vcc )
JOLLY SERIES DRIVEmod. 10/120 ( 10A nominali 20A picco / 120Vcc )
JOLLY SERIES DRIVE mod. 14/120 ( 14A nominali 28A picco / 120Vcc )
JOLLY SERIES DRIVEmod. 8/150 ( 8A nominali 16A picco / 150Vcc )
JOLLY SERIES DRIVEmod. 12/150 ( 12A nominali 24A picco / 150Vcc )
JOLLY SERIES DRIVEmod. 8/200 ( 8A nominali 16A picco / 200Vcc )
MASTER SERIES DRIVEmod. 18/150 ( 18A nominali 36A picco / 150Vcc )
MASTER SERIES DRIVEmod. 28/150( 28A nominali 56A picco / 150Vcc )
MASTER SERIES DRIVEmod. 18/200 ( 18A nominali 36A picco / 200Vcc )
MASTER SERIES DRIVEmod. 25/250 ( 25A nominali 50A picco / 200Vcc )

MASTER DRIVE MANUAL (only in Italian)
JOLLY DRIVE MANUAL (only in Italian)

 

 

0 Continue Reading →

Brushless

MOTORS/DRIVES “R” SERIES

Low inertia motors for rapid acceleration and placements. Medium inertia motors for low speed. Connectors version (encoder/motor phases) and cables with connectors. Power range from 50 to 3000 W (from 0.16 to 10 Nm) equipped with incremental encoder pulses 2000 (8000 by the driver). Closed loop drives, configurable via RS232. Control mode, speed, torque.

Dynamic Autotuning (prevents calibration process). Oscilloscope function for speed and torque used. Single/three-phase power supply 200-230 VAC. Max current. payable 15, 30, 50, 100 Amp.

MOTORS, DRIVES, SERIES “B”

AC synchronous servomotors with 540 V DC bus for digital converters supplied by 400 VAC three-phase network.
High and low-inertia models.
Holding torque up to 100 Nm.
speed up to 6000 rpm Standard, short, forced cooling, water cooling.
Feedback with resolver, Sincos encoder, EnDat and incremental encoder.
Brake options, available complete with coaxial planetary gear or bevel gearbox.

Power and signal cables with connectors Synchronous-asynchronous drives in digital direct-phase network power 180 …-528 VAC 50 60 HZ (also possible in single-phase)
DC bus voltage 540
Power range up to 300kW
Single axis, multiple architectures.
Open modular systems with fieldbus access communications such as:
CANsync, Canopen, Profibus DP, Sercos.
Incremental encoder Digital Analog Simulator.
Feedback from resolver 2 poli, SinCos, EnDat, incremental encoder.
Axis modules/PLC incorporated.

sidac-system


  • Applications where  high speed constant torque are required
  • Packaging and printing (sheet feeding)
  • Paper products
  • Machinery for food processing
  • Packanging machines
  • Pumps and fans
  • Textile industry
  • Machine tools
  • Handling and tran sport of semiconductors
  • Cutting machines
  • Industrial robots
  • Flying saw Sistemi taglio al volo
  • Plastics processing

Dmensioni modulo assi

Brushless

 

0 Continue Reading →